| Customization: | Available |
|---|---|
| Output Type: | Dual |
| Warranty: | >2 Years |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Main Component | Description |
| Onboard Module(ESP32-S2-SOLO or ESP32-S2-SOLO-U in the figure above) | ESP32-S2-SOLO series module, can be equipped with a PCB onboard antenna or an external antenna connector, and supports various flash and PSRAM sizes. For more information, please refer to the Ordering Information. |
| 3.3 V Power On LED | This LED lights up when the board is powered via USB. |
| USB-to-UART Bridge | A single-chip USB to UART bridge, providing transfer rates up to 3 Mbps. |
| Pin Headers | All available GPIO pins (except the SPI bus for flash) are broken out to the pin headers on the board. See Pin Layout for details. |
| ESP32-S2 USB Port | ESP32-S2 USB OTG interface, compliant with the full-speed USB 1.1 standard. This port can be used to power the board, flash firmware to the chip, or communicate with the chip via USB protocol. |
| Reset Button | Resets the system. |
| Boot Button | Download button. Hold down the Boot button and then press the Reset button to enter "Firmware Download" mode for flashing firmware via the serial port. |
| USB-to-UART Port | Micro-USB port. Can be used to power the board, flash firmware to the chip, or as a communication interface to interact with the ESP32-S2 chip via the onboard USB-to-UART bridge. |
| RGB LED | Addressable RGB LED, driven by GPIO18. |
| 5 V to 3.3 V LDO(Low-Dropout Regulator) | Power converter. Input 5 V, output 3.3 V. |
| Getting Started with Development | |
| Before applying power, ensure the ESP32-S2-DevKitC-1 is in good condition. | |
| Hardware Required | |
| ESP32-S2-DevKitC-1 | |
| USB 2.0 cable (Standard-A to Micro-B) | |
| PC (Windows, Linux, or macOS) | |
| NO. | P/N | MCU | Flash / PSRAM | Interfaces | Description |
| 1 | ESP32-P4-Function-EV-Board | 32-bit RISC-V MCU | 16 MB Flash on board; 32 MB in-package PSRAM; 4 MB in-package flash in ESP32-C6-MINI-1 | MIPI CSI, MIPI DSI, USB RJ45, I/O, TF card |
ESP32-P4-Function-EV-Board is a multimedia development board based on the ESP32-P4 chip. ESP32-P4 chip features a dual-core RISC-V processor and supports up to 32 MB PSRAM. In addition, ESP32-P4 supports USB 2.0 specification, MIPI-CSI/DSI, H264 Encoder, and various other peripherals. With all of its outstanding features, the board is an ideal choice for developing low-cost, high-performance, low-power network-connected audio and video products |
| 2 | ESP32-S3-DevKitC-1 | 32-bit MCU & 2.4 GHz Wi-Fi & Bluetooth 5 (LE) | 8 MB Flash 8 MB Flash + 3.3V 2 MB Quad PSRAM 8 MB Flash + 3.3V 8 MB Octal PSRAM 32 MB Flash + 1.8V 16 MB Octal PSRAM (Suitable for ESP32-S3-WROOM-2) |
I/O USB |
ESP32-S3 general-purpose development board, based on ESP32-S3-WROOM-1/1U or ESP32-S3-WROOM-2/2U. It has all the ESP32-S3 pins exposed and is easy to connect and use. |
| 3 | ESP32-S2-DevKitC-1 | 32-bit MCU & 2.4 GHz Wi-Fi & Bluetooth 5 (LE) | 4MB Flash, 8MB Flash + 2 MB PSRAM | I/O USB |
ESP32-S2 general-purpose development board, based on ESP32-S2-SOLO series. It has all the ESP32-S2 pins exposed and is easy to connect and use. |
| 4 | ESP32-C3-DevKitM-1 | 32-bit RISC-V MCU & 2.4 GHz Wi-Fi & Bluetooth LE 5 (LE) | 4 MB Flash | I/O USB |
ESP32-C3-DevKitM-1 is an entry-level development board based on ESP32-C3-MINI-1 or ESP32-C3-MINI-1U, modules named for its small size. This board integrates complete Wi-Fi and Bluetooth® Low Energy functions. |
| 5 | ESP32-C5-DevKitC-1 | 32-bit RISC-V MCU & 2.4 and 5 GHz Wi-Fi 6 & Bluetooth 5 (LE) & IEEE 802.15.4 | 8 MB Flash + 4 MB PSRAM | I/O USB |
ESP32-C5-DevKitC-1 is an entry-level development board based on the general-purpose module ESP32-C5-WROOM-1(U). This board integrates complete Wi-Fi, Bluetooth LE, Zigbee, and Thread functions. |
| 6 | ESP32-DevKitC | 32-bit MCU & 2.4 GHz Wi-Fi & BT/Bluetooth LE | 4 / 8 MB Flash | I/O USB |
ESP32-DevKitC is a small-sized ESP32-based development board produced by Espressif. Most of the I/O pins are broken out to the pin headers on both sides for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-DevKitC on a breadboard. |
| 7 | ESP32-LyraT-Mini | 32-bit MCU & 2.4 GHz Wi-Fi & BT/Bluetooth LE | 8 MB Flash + 8 MB PSRAM | I2S I2C SDIO ADC UART GPIO |
ESP32-LyraT-Mini is a lightweight audio development board based on ESP32-WROVER-E, which implements AEC, AGC, NS WWE (wake word engine) and other audio signal processing technologies. |
| 8 | ESP32-PICO-KIT-1 | 32-bit MCU & 2.4 GHz Wi-Fi & BT/Bluetooth LE | 4 MB Flash | I/O USB |
The ESP32-PICO-KIT-1 is an ESP32-based development board produced by Espressif. ESP32-PICO-KIT-1 provides users with hardware for development of applications based on ESP32, making it easier for users to explore ESP32 functionalities. |
| 9 | ESP32-S3-BOX-3 | 32-bit MCU & 2.4 GHz Wi-Fi & Bluetooth 5 (LE) | 1.8V 16 MB Quad Flash + 1.8V 16 MB Octal PSRAM | USB I/O, Pmod™ Compatible Interlace, MicroSD Slot, 18650 Battery Slot |
The ESP32-S3-BOX-3 is a next-generation development tool designed for AIoT, Edge AI, and IIoT applications. It is based on the powerful ESP32-S3 SoC and features a compact and beautiful enclosure also provides rich assemblies, empowering developers to easily customize and expand its functionality. |
| 10 | ESP32-C6-DevKitC-1 | 32-bit RISC-V MCU & 2.4 GHz Wi-Fi 6 & Bluetooth 5 (LE) & IEEE 802.15.4 | 8 MB Flash | I/O USB |
ESP32-C6-DevKitC-1 is an entry-level development board based on ESP32-C6-WROOM-1(U), a general-purpose module with an 8 MB SPI flash. This board integrates complete Wi-Fi, Bluetooth LE, Zigbee, and Thread functions. |
| 11 | ESP32-S3-EYE | 32-bit MCU & 2.4 GHz Wi-Fi & Bluetooth 5 (LE) | 8 MB Flash + 8 MB PSRAM | USB | The ESP32-S3-EYE board consists of two parts: the main board (ESP32-S3-EYE-MB) that integrates the ESP32-S3-WROOM-1 module, camera, SD card slot, digital microphone, USB port, and function buttons; and the sub board (ESP32-S3-EYE-SUB) that contains an LCD display. The main board and sub board are connected through pin headers. |
| 12 | ESP Thread Border Router/Zigbee Gateway | 32-bit RISC-V MCU & Bluetooth 5 (LE) & IEEE 802.15.4 | 8 MB Flash and 2 MB PSRAM in ESP32-S3-WROOM-1 + 2 MB Flash in ESP32-H2-MINI-1 | I/O USB type-C |
ESP Thread Border Router/Zigbee Gateway board integrates the ESP32-S3 SoC and the ESP32-H2 RCP, enabling the development of Thread Border Router and Zigbee Gateway products. Espressif's Thread Border Router solution complies with Thread 1.3 and supports the Matter application. |
){kind=link}